EBXYAXLR Microphone Cable, 3ft XLR Cable Audio Cords Microphone Patch Cable Balanced, 4 Color Packs

They were everything I needed and received them from Amazon very fast. Very satisfied

The plugs feel solid and connections are tight. I bought these for a church sound system and the color coding helps when identifying which mic is which. I would buy these again.

We are using them our stream and it works great.

great

To avoid cable clutter, our band uses these three foot patch cables to connect wireless microphone receivers to the PA head at shows instead of having 25' cables on wired mics. We color coded everything so that each person's gear is always put back together, and so that it's easy to see who gets plugged in where. Bought these to replace the black cables with colored tape markers and painted plugs.Just received these and pulled them out of the bag. They came with twist ties attached and a set of 6 velcro cable wraps that will attach to the wires for easy storage. The colors look nice and the cable is quite flexible. The connectors seem solid, but there doesn't appear to be any indexing in the female end to force the pins to align correctly with the tab if you were to unscrew the connector to look inside - you must manage this manually, by eye. The color on the connectors is in the form of a plastic ring that could crack with rough use, but seems durable enough for almost any job and is redundant, since you can't miss the color of the cable. I did plug the connectors into each other, and to a couple microphones and a recording interface I had handy. I have had problems with loose or, worse, overly tight fits in the past that have caused problems with gear. These fit perfectly well and felt quite solid plugging in and out.The big downer is that there is no shrink tubing added at the ends to create a strong strain relief. The cable itself is flexible and may be a hair smaller in diameter than some others, and the plastic strain relief built into the connectors doesn't grab the cable firmly enough to provide the level of protection I prefer. If you never yank on these or try to pull them out by the wire, they should hold up fairly well, but I wouldn't count on reliability if these are in a higher traffic area or careless users go yanking on the female wire end instead of the connector to unplug them. You get what you pay for on these.I will probably unscrew all the connectors and add either a wrap or two of electrical tape or paint on some liquid electrical tape to add a little diameter where the cable runs through the connector's built-in strain relief and that will improve the durability. I use the correct diameter of heat shrink tubing on the cables I build, and I may decide to install some on these, but it's a hassle to desolder and resolder an end to make that happen. I only needed three, so I'll probably carry the other three as spares and add proper strain relief if they do fail in use.Still, the lack of sufficient strain relief reduces my confidence in the product and I can't recommend them as highly as I would like to. These would be 4.5-5 stars with proper strain relief. If I held back the last half star, it would be for the lack of indexing in the female plug, but that's something 99% of users are never going to notice.We're going to test them before they get used at a show, but these seem like they'd be a great cable for casual or protected use, and good enough to give them a shot on stage.

I use this for professional gigs. Saves a lot of guesswork as to what went where, in the event of a malfunction or addition.

I was expecting a more rubbery covering to the cable. With the more vinal cover, the cable is alittle stiffer on stage then I care for. When you have six+ mic channels covering a drum kit, its nice to have flexable stuff because it lays down out of the way

This is a connect once and live there forever sort of install, so I hoped to get away with something less expensive. so far I detect no issues and I think this will work well for a long time. great for connections between DI's and the Mixer, or between External processors and the board, with out using inserts. In this application, there will be no patching or changing the sources or the configuration. My use is unique in that we are a Ham Radio station, as well as GMRS Radio and we Live Stream a weekly "net" broadcast. Audio is coming in from vocal mic's, and from two way radios through direct boxes, and being mixed and returned to two way radios and a PC for the live stream. I hope this helps you understand my application and is useful in determining if these cables will work for you. BTW, the color coding is far more useful than I would ever have expected, having used only black mic cords.Best of luck

I bought these because I was using a mike on a desk, through a DI box into the computer, with a 3m XLR cable, which was ridiculous! These patch leads are ideal for the job, and I've since found other applications for them. Sound quality is pretty transparent as far as I can tell, they seem durable enough for purpose (I'm not going to be throwing this mike around a stage or anything) so well worth buying.

Love the colour. Length is perfect. Quality is awesome.

Great set of XLR cables with colour coding to identify each source and input. Perfect for our Audio Interface. Very well made.

See title

BARGAIN!!